Your browser is no longer supported

For the best possible experience using our website we recommend you upgrade to a newer version or another browser.

Your browser appears to have cookies disabled. For the best experience of this website, please enable cookies in your browser

We'll assume we have your consent to use cookies, for example so you won't need to log in each time you visit our site.
Learn more

Reclaiming the streets

Sydney Sydney's streets will be transformed when the Cross City Motorway tunnels open. Ruby Kitching reports.

Sydney is fighting roadclogging traffic by building two new toll roads beneath the city.

Sydney mayor Clover Moore says the US$750M Cross City Tunnel scheme will enable motorists to cross the city in just two minutes instead of the 20 it takes at present. And pedestrians will have fewer cars to dodge. Peter Samson, chief executive of tunnel operating company Cross City Motorway (CCM) confirms: 'It's about giving the streets back to the people.' By October this year, two 2.1km long tunnels will have been burrowed east-west under Sydney's central business district between Darling Harbour and Rushcutters Bay. CCM is responsible for design and construction of the link, as well as its operation and maintenance for 30 years. It will eventually be handed over to the New South Wales government. A joint venture of contractors Baulderstone Hornibrook and Bilfinger Berger completed the tunnels - plus a ventilation tunnel - last month using road headers with cut and cover techniques at the tunnel portals.

Need for the Cross City Tunnel stems from the way Sydney has changed over the years. Traffic flow was originally orientated north-south for access to the harbour crossings. But as the central business district developed, Darling Harbour sprouted hotels and restaurants, a new airport was built south west of the city, and traffic patterns changed. Crossing the city centre from east to west became more and more difficult for drivers, and pedestrians were increasingly marginalised.

Despite the tunnels' benefits, the people of Sydney started out very sceptical about the project. Traffic disruption and settlement problems were caused by construction of the Eastern Distributor Tunnel six years ago, and locals wanted to make sure they had a greater say on how the project was programmed.

Seventy percent of the project was constructed using cut and cover with nine construction sites edging to within 2m of buildings.

Concern has focused mostly on noise and vibration from tunnelling. 'If a person rings up complaining about their cutlery rattling, we have to go down and measure the vibration within two hours, ' says BHBB project superintendent Geoff Foster.

'Sometimes people prefer that you work for three days straight and three off instead of working shorter days for a week, ' adds Samson.

An extra ramp to link the tunnels with the Eastern Distributor dual carriageway was built to enable extraction of spoil without clogging up the city's streets. And the road header launch pit has been shrouded by a soundproofed building to reduce noise impact, allowing 24 hour tunnelling to take place.

Tunnelling began at the centre of the route in January 2003 so that cut and cover construction at the portals could proceed at the same time.

Nine road headers have carved an 8.6m wide by 7.8m high face through the tough sandstone rock underlying Sydney, covering up to 6m a day. The tunnels have a wide, square section.

Rock is competent, and tunnel has been advanced in 600mm lengths, with rock bolts at up to 2m centres and two 50mm thick layers of sprayed, steel fibre reinforced concrete being used to support the walls and face.

These form the final lining.

The road headers are guided by on-board computers. 'This has sorted out a big safety issue - you don't have surveyors with spray cans walking around the back face any more, ' says Foster.

At its deepest, the tunnel is 53m below ground level, meaning that settlement risk is minimal. Risk to buildings is further reduced by routing the tunnel over most of its length under William Street, a principal thoroughfare. This solution is not without hitches, however, as William Street is also the main route for utilities.

'The main electricity supply passes through the Druitt Street portal and had to be incorporated into the design, ' says Foster. He adds that some service ducts were so heavy they were originally supported by piles. These have been removed and replaced by steel transfer structures.

Have your say

You must sign in to make a comment

Please remember that the submission of any material is governed by our Terms and Conditions and by submitting material you confirm your agreement to these Terms and Conditions. Please note comments made online may also be published in the print edition of New Civil Engineer. Links may be included in your comments but HTML is not permitted.